Repairs · Guide
Solar inverter red light or beeping: what it means
Most of the time a solar inverter sits quietly on the wall and nobody looks at it. Then one day there’s a red light, a flashing green one, or a beep you haven’t heard before, and it’s hard to know whether it matters.
Mon–Fri 9:00am–5:00pm · Clear written quote before any work starts
Talk to us about solar, batteries or repairs.
Call 0800 156 0191, Monday to Friday, 9:00am–5:00pm, or send us a message through our contact page.
MCS certified
NAPIT registered
TrustMark approved
Fully insured
England, Wales & Scotland
Why lights
Why inverters have lights at all.
The lights and sounds are the inverter’s way of telling you what it’s doing. Some are perfectly normal. Others mean it has stopped producing power and needs attention. This guide explains what the common signals mean, what you can safely check from the ground or the fuse board, and when it’s time to call an engineer. If your inverter is also showing a code on its screen, read our guide to solar inverter error codes alongside this one.
The inverter turns the direct current (DC) from your panels into the alternating current (AC) your home uses. Because it does this silently, manufacturers fit coloured lights, and sometimes a buzzer, so you can see its state at a glance.
The Energy Saving Trust says the handover information from your installer “should include details of the main inverter fault signals and key troubleshooting guidance.” If you still have that pack, or the inverter’s user manual, it is the best guide to your exact model. Colours and patterns are not the same across brands, so treat the examples below as a starting point rather than a rule.
Green
Green lights: usually good news.
On most inverters, a steady green light means the system is producing power and feeding it to your home.
- SMA Sunny Boy (3000TL–5000TL range): green glowing means feed-in is active. Green flashing means “The conditions for feed-in operation are not yet met”, for example early in the morning.
- SolarEdge single-phase HD-Wave (Europe): “Green ON – the system is producing” and “Green blinking – AC is connected but the system is not producing.”
- Fronius Primo: the operating status LED is green when the system is working without faults after its automatic start-up.
A flashing green light at dawn, at dusk or on a very dull day is normal. A flashing green light at midday on a bright day, every day, is worth a closer look.
Red
Red lights: something has stopped it.
A red light almost always means a fault or an event the inverter can’t clear on its own.
- SMA: red glowing means “An error has occurred”, and the manual adds that “The error must be rectified by a qualified person.”
- SolarEdge: “Red ON – system error.”
- Fronius Primo: the red general status LED lights when a status message is on the display, when feed-in has been interrupted or during fault handling.
Some red-light faults clear themselves. A brief grid problem, such as the mains voltage going outside its limits, can stop the inverter for a few minutes until the supply settles. In Great Britain the declared supply is 230 volts, and the regulations allow “a variation not exceeding 10 per cent above or 6 per cent below” that figure. Other red-light faults, such as an isolation (earth) fault, point to a problem in the cabling and need an engineer. See our guide to isolation faults.
Orange and blue
Orange and blue lights.
An orange or amber light usually means the inverter is starting up, testing itself or updating. On a Fronius Primo, the orange start-up LED is lit “when the inverter is in its automatic startup or self-test phase”, and also in standby and during software updates. If it stays on start-up or standby all day, see inverter stuck in night mode.
A blue light normally relates to communication. On SMA models, blue means Bluetooth is active. On SolarEdge HD-Wave models, blue on means the inverter is talking to the monitoring platform. A missing blue light often explains why your app has stopped updating, even though the panels are still producing. Our guide to solar monitoring that has gone offline covers this.
Beeping
Why is my inverter beeping?
Many string inverters are silent, but hybrid inverters and battery systems often have a buzzer. Manufacturers list several common reasons. SolaX, for example, names grid overvoltage, overloading the backup supply during a power cut, a low battery, an isolation or earth fault, overheating and communication errors. It also notes that short beeps at dawn or dusk can simply mean there is just enough light for the inverter to wake up.
The one to take seriously is an isolation or earth fault. SolaX’s advice is “Do not reset” the system or inspect the wiring yourself. A beep with a burning smell, smoke or scorch marks means switch nothing on and call for help. Humming and buzzing are a different matter and are covered in our guide to inverter noise and overheating.
Safe checks
What you can safely check.
You don’t need to go near the panels or the DC cabling to gather useful clues. Please:
- note the colour of each light, whether it is steady or flashing, and the time of day;
- take a photo of the screen and any code shown;
- check the fuse board for a tripped breaker labelled solar or PV, but don’t keep resetting it if it trips again (see tripping RCD);
- check whether your generation meter is still counting on a bright day;
- look at the monitoring app for when the problem started.
Please don’t open the inverter, switch DC isolators, or climb onto the roof. Panels are live in daylight, and the DC side can carry a dangerous voltage even when the inverter is off.
Call us
When to call an engineer.
- The red light stays on, or comes back day after day.
- The inverter shows no lights at all in daylight.
- The screen or app mentions isolation, earth, insulation or leakage.
- The beeping won’t stop, or comes with heat, smoke or a smell.
- Output has dropped and the generation meter has slowed or stopped.
Inverters typically last 10 to 15 years, so an older unit with repeated faults may be near the end of its life. Our guide to how long solar inverters last explains the choice between repair and replacement.
How we help
How we help.
We install our own systems and repair everyone else’s, so we know exactly how they fail. Our own engineers work on systems fitted by any installer, on any brand, across England, Wales and southern Scotland, and that includes diagnosing beeping and alarm faults on hybrid and battery inverters, such as backup overload and low-battery alarms. We have brand guides for SolarEdge, SMA, Fronius and others.
Repair is our core business, so there’s no pressure to rip out and replace. We offer same-week inverter repair or replacement, and you get a clear written quote before any work starts. Find out more about solar inverter repair.
Sources: SMA Solar Technology, Sunny Boy 3000TL–5000TL operating manual; SolarEdge, Single Phase Inverter with HD-Wave Technology Installation Guide (Europe and APAC); Fronius, Fronius Primo Operating Instructions (2024); SolaX Power, Why is my solar inverter beeping? (2026); Energy Saving Trust, Solar panels; Electricity Safety, Quality and Continuity Regulations 2002, regulation 27.
Questions
The things people ask before they ring.
Not answered here? Call 0800 156 0191, Monday to Friday, 9:00am–5:00pm.
What does a red light on my solar inverter mean?
On most models it means a fault or error has stopped the inverter. Some clear themselves after a grid problem; if it stays on, have the system checked.
Is a flashing green light on my inverter a problem?
Usually not. It often means the inverter is waiting for enough light to start. If it flashes all day in bright sun, it may not be producing.
Why does my solar inverter beep?
Common reasons include grid voltage problems, a low battery, overloading in backup mode, overheating and earth faults. Note what the screen says and when it happens.
Can I reset my inverter myself?
Follow your manual’s user instructions only. Don’t switch DC isolators, and don’t keep resetting a fault that comes back, especially an earth or isolation fault.
Why is the blue light off on my inverter?
On many models blue shows communication with the app or monitoring platform. If it’s off, the system may still be producing, but the data link has dropped.
Ready when you are
Red light or beeping inverter?
We’ll call you back to talk it through, and you get a clear written quote before any work starts. Mon–Fri 9:00am–5:00pm.

